Author Archives: Slab Leak Solutions

How to Find a Plumbing Leak

water leak damage

Finding hidden leaks

Water is a wonderful natural source that we need in our everyday lives. It is also an enemy to our homes when it is in places it shouldn’t be, like from a plumbing leak in any number of places. This is why plumbing leak detection is so important for a homeowner. 

Plumbing leak detection is important not only for saving our homes, but a natural resource that isn’t replenishing as fast as we’re using it. According to the EPA (Environmental Protection Agency), the average household leaks account for as much as 10,000 gallons of water, or more, each day. That is wasted water for the environment and wasted money on higher water bills, and let’s not forget the damage it is doing to homes. 

A homeowner that gets a water bill with a higher than normal amount can do some plumbing leak detection, even though they won’t have all the equipment, experience, and skills that a professional plumber does.  By professional means, these steps are nothing like a professional plumbing leak detection, and it certainly won’t pinpoint if you have a plumbing leak in slab, a plumbing leak in wall, or any specific area. These steps will only confirm your suspension. 

For this simple plumbing leak detection of your home’s plumbing secretly wasting water, follow these steps, preferably when nobody else is home so there isn’t any accidental flushing or water being turned on: 

  • Make sure all the water outlets are turned off, inside and outside of your home.
  • Find the water meter and write down the reading on the meter. 
  • Wait at least one hour then  check the water meter reading.
  • If the numbers have changed, you have detected a plumbing leak.

Now, the question is where and how bad, and for a homeowner, there isn’t any way of plumbing leak detection in hidden areas like the slab foundation or inside a wall.  For a leak in an upstairs bathroom, one plumbing leak in ceiling would be water stains on the ceiling directly under that bathroom. 

Turning the water back on and check under all the sinks for plumbing leak under sinks. While you may think this would be an obvious place you’d have noticed already, it could be very small and undetected.  As the water is turned back on, check the plumbing under each sink and around each toilet. 

For those hidden plumbing leak detection methods, you’ll need a plumber with professional plumbing leak detection equipment. Today, one of the plumbing leak test a plumber can perform is a hydrostatic pressure test. This is performed on your home’s sanitary sewer system  and can detect any water leaks in the plumbing system. 

  • First, the plumber inserts an inflatable test ball into the mainline of the sewer clean out, a hydrostatic plumbing leak detection method. 
  • Then the  test ball is inflated so that it blocks the main sewer line. The water is then turned on until the sewer system is  filled to the slab level with water. 
  • The plumbing contractor will then observe the water level for 15 minutes. If the water in the sewer system doesn’t reach the slab level, or begins to lower, this indicates a leak in the sewer system. 

Another piece of  plumbing leak detection equipment used to identify where the leak is using a higher level of technology. That plumbing leak detection involves using video camera on a fiber optic cable and a television-type screen.  

The fiber optic cable and camera are inserted into the suspected problem pipe and the camera sends pictures back to the television-type screen. The plumber is able to see exactly where the leak is and determine what needs to be done. 

Another method that professional plumbers use for plumbing leak detection is with an electronic listening device. This technology enhances  the plumber’s hearing so that they can hear deep inside the water lines. This allows them to narrow down the area of the plumbing leak by inducing a small electric charge in the water lines. 

It is important that a homeowner realize any plumbing leak or roof leak that goes undetected, or left unrepaired, the dangers and risk they are putting their family and home in jeopardy. A plumbing leak and mold go hand in hand, and becomes expensive not only with the structure damage, but the health of their family. 

copper pipe leak

Is plumbing leak covered by insurance?

There are several factors that are considered by an insurance company before they will pay a claim.  A roof leak in a roof that is over a certain age or has been neglected by the homeowner, any insurance claim will be declined. Damage from acts of nature like tornados that cause roof leak, the claim will likely be paid. 

Plumbing leaks are a different breed of insurance claims. It may not pay for the repair, but it will pay for the replacement of things damaged by a plumbing leak. Detection equipment will become more commonplace, and homeowner’s insurance will likely start offering discounts for homes equipped with plumbing leak detection, if they haven’t already. Need help finding your plumbing leak in Fort Worth, TX? Call 817-281-5325 today.

Is a slab leak covered by home warranty?

slab with leak below it

What happens if you have a slab leak?

Insurance and warranty, two things we learn can be a lot of help, but they can also be useless at times.  However, we need them, especially when you buy a home or a vehicle, with one of them being required by your bank and the law. Do either of them offer slab leak coverage?  Keep reading and we’ll answer that question along with a few others.

First, what is a slab leak? A slab is what many homes are built on and inside that slab is the plumbing. When that plumbing develops a leak, that is a slab leak, and it isn’t good!  If you thought the Watergate leak coverage was bad news, that isn’t anything compared to when your plumber tells you have a slab leak. Coverage of this catastrophe is what we’re going to discuss here. 

A slab leak will cause a lot of damage to a home, sometimes before you even realize you have a slab leak. As a homeowner, you should need to be aware of several things that can tell you there may be a possible slab leak, coverage of damages happening could be not only the foundation (the slab) but it will get worse. 

The plumbing will come loose, the foundation will break, crack, even sink in places. Your flooring will be damaged along with the walls and in time, the ceiling can be affected by a slab leak. Coverage in water from that slab leak will affect the electrical wiring, even gas lines are in danger of shifting and breaking, developing a leak. 

A few ways to tell that you have a slab leak, coverage of water is in process under your home are: 

  • A Hot Floor: When a slab leak happens, the hot water will warm the floor because it has leaked in and under the slab. You may notice your water heater is running constantly, even when you haven’t been using any hot water. 
  • Sounds of Water:  When you hear sounds of water running or rushing in the bathroom, kitchen, laundry room, or near the water heater, but none of the fixtures are on, you probably have a slab leak. Coverage of water is ensuing as you hear that water running.  
  • High Water Bill: When your water bill has jumped up more for no apparent reason, like out of town guests, especially if it remains high the next month, you probably have a slab leak. 
  • Damp Carpet or Flooring: Damp wet flooring is probably the most obvious indication of a slab leak. Water is a powerful source, even at a trickle, and it will find the path of least resistance. As it begins to accumulate in an area, it will pool up and spread out, your slab leak coverage of water  is going to expand at that point, fast. 
  • Low Water Pressure: If you notice that your  water pressure has dropped, that is probably the water leaking into the slab from a busted pipe. 

Now that you know what to look for in a slab leak, what the heck caused it? As we explained, the water pipes in your home are under the slab. Here in Texas, it is well known the ground shift with the weather, meaning it gets wet and swells, then it dries out and contracts.  

The plumbing that has been used in homebuilding for centuries can only take so much flexing.  Some plumbing materials, copper, galvanize steel, and others, will fight the chemical compost of the slab concrete and the slab wins, and you get a slab leak, coverage in water, as the prize. 

Can a slab leak cause foundation problems?

When a slab leak isn’t detected, or it is ignored, you are setting your home up for serious problems and the consequences aren’t going to be cheap. The following is just a few things that you can expect to happen with a slab leak: 

  • A large slab leak will soak the soil around and under the cement slab of you home, then wash that soil away. The cement slab has nothing holding it up now, so it shifts, sinks, cracks, and drop off. 
  • As the slab shifts, sinks, cracks, and drops off, the flooring and walls will give with it, and eventually the ceiling will start shifting with it all. 
  • That moisture from the slab leak, coverage of water seeps into those cracks and up your house, mildewing the flooring, walls, and the mold takes over, weakening your home’s very structure. 

Is a slab leak covered by insurance, will insurance cover slab leak?

Oh the number of times insurance companies are asked about  slab leak and insurance coverage!  Homeowners need to review the homeowner’s insurance policies once a year and update their memory on slab leak coverage. Will your homeowner’s offer any slab leak coverage? Will, you’ve heard before, it depends. 

The two main causes of a plumbing failures in a home. Frozen pipes win with 48% of claims, something that could often have been avoided with some preparation by the homeowner.  The other cause is material failure, meaning, the plumbing materials were weak or installed poorly. 

Before your homeowner’s insurance will approve any slab leak coverage, it needs to cover these three conditions, and even then, the coverage is going to be minimal at best:

  1. There must be evidence of slab leak damage to the home.
  2. Your homeowner’s policy has water damage coverage.
  3. The damage must have happened suddenly, not a long time of slow destruction. claim.

Two other factors that could be essential in having slab leak coverage would be:

  • If slab leak damage was done by failure of homeowner maintenance or tree roots. 
  • Homeowners insurance policies in Texas typically exclude any type of foundation coverage because the soil is mostly clay. A soil that is known to shift. Some insurance companies will offer a  water and foundation endorsement with a coverage up to 15% of the Coverage A stated in the policy. Typically a maximum of $25,000.
home with a slab

Do home warranties cover slab leaks?

Some do, some don’t.  Again, you need to review your policy every so often, so you have fresh memory of what is covered.  A slab leak can be caused by poor design,  construction, or the pipes could be damaged during construction. In that case, you may have slab leak coverage through your home warranty policy, even if you aren’t the original owner. New built homes typically have slab leak coverage for a period of time, you’ll want to consult with the builder for that coverage. 

Every homeowner will try (or should) find some way to get assistance in paying for major repairs around the home, understandable. So, if you happen to have a home in an HOA, does hoa cover slab leak? Well, if your home is a stand-alone house that is in an HOA, probably not, but the bi-laws and CC&R will provide you more exact details to this matter.  You can be certain though that they will be in your business on finding the right plumber that knows how to fix slab leak and in short time.  However, typically slab leak coverage in a condominium development is covered by the association. Call 817-281-5325 today for your slab leak repair needs in Fort Worth, TX.

How Much Does it Cost to Repipe a Whole House?

pipe bursting

 Why repipe a house?

Sometimes, a house has so many plumbing issues, especially an older home, that the best solution is to repipe the entire house.  What does repipe mean? In the plumbing industry, repiping is when thepipes in your home are completely replaced after the current pipes are removed.

A standard repipe project includes installing all-new cold and hot domestic water piping from the source to all the faucets and fixtures in the home. Drainage and sewer lines are not included in the basic repipe job. What is typically included in a home repiping job is:

  • New connections at the hoses.
  • New valves at each sink and toilet.
  • New water supply lines.
  • New main shut off to the house and the water heater.
  • New box and valves in laundry box.
  • New ice maker box.

One of the biggest factors that determine if a house needs to a repipe job is the age. A house that was built in 1970 or earlier likely has galvanized plumbing  pipes or other out-of-date metal.  Around 1970, copper for the plumbing because of the durability.

 Or they used PVC because of its durability and resistance to corrosion. In recent years, PEX has become the go-to pipe in plumbing, because it is even more durable than PVC and remains flexible regardless of the temperature. For a home built prior to 1970, and certainly prior to World War II, the plumbing is almost certain in need of a repipe project.

When should you repipe a house?

Some of common reasons a homeowner decides to repipe their home would include:

  • An older home.  A house that is older than 50 years and has the original plumbing probably has galvanized pipes. By now, they are corroded and prone to bursting under the least amount of pressure or stress.
  • Low water pressure. If the water pressure in your faucets is weak, the pipes are probably closing up from mineral build up and rust over time.  
  • Brown or red water. Some household pipes will rust over time, and eventually, the water will turn brown or red. The only solution is to repipe the house because by that point, the entire plumbing system now has rusted water running through it.
  • Multiple water leaks. Having an isolated water pipe leaks isn’t anything of concern other than fixing it, but when you have multiple leaks in a short period of time, repipe the plumbing system is the best solution. It is an investment that will have ROI because you won’t be paying a plumber one or two times a month to fix leaking pipes.

How much does it cost to repipe a hole house?

You’ll want to call two or three plumbing contractors for estimate to repipe your home. This will give you an exact amount and the opportunity to compare pricing and services.  The cost to repipe a home has a few factors to be considered:

  • Material used
  • Size of the home
  • One story or multiple stories
  • Number of bathrooms
  • Additional water fixtures

A complete house repipe job can start around $4,000 and go up to $15,000 with PEX material for the repipe work. PEX is more expensive than other options, but it doesn’t require as much demolition to install. That helps reduce the cost overall when compared to copper or PVC.

How much does repipe cost?

Cost to repipe with pex material (cross-linked polyethylene tubing) can cost between fifty cents per foot to $2 per foot. PEX is a flexible plastic hose that plumbers can “snake” into and through walls with little to no need to tear out walls. PEX is better for cold weather because it doesn’t freeze like copper or PVC pipes, so there is no worry about busted pipes as they thaw in the winter.

Where you live will have an impact on what a plumber will charge for any type of work like the cost to repipe kitchen sink. The next factor that can impact the cost is the difficulty of the work to be done. On average, a plumber charges between $45 and $150 per hour plus the parts. So to repipe a kitchen sink, you could be looking at $125 to $300, depending on if a new sink is involved and any special plumbing needs like hot water faucet or garbage disposal.

sewer pipes

Are polybutylene pipes bad?

PB pipes (polybuthlene) are typically used inside walls. If they begin leaking, it isn’t always noticed right away. By the time it is noticed, serious damage has already happened. This can lead to mildew, mold, and more issues that costs to get repaired.

Should you decide your home needs to have a repipe job done, get 2 to 3 quotes from experienced, licensed, qualified plumbers that know how to repipe a house. You want a Master Plumber, not an apprentice in charge of the job to assure it is done correctly. Ask for current references and then contact those references. The best advertisement any business or contractor can have is word of mouth. Call 817-281-5325 today for your whole house repiping in Fort Worth, TX.

Identifying a slab leak within your home

foundation slab

Signs of a slab leak

We’ve discussed how devastating a water leak can be, but when that water leak is a slab leak, the devastation can be much, much worse. To clarify, a slab leak is when a water or sewer line that is buried under your home’s slab breaks or has deteriorated and water seeps into he foundation, causing it to crack and water infiltrates the slab. To repair a slab leak, estimates can be anywhere between a few hundred dollars to thousands of dollars, and that doesn’t count repair or replacing what was damaged by the slab leak. 

Let’s get the most common question answered now: Are slab leaks covered by homeowners insurance?  The answer isn’t what you want to hear: No, not usually.  Homeowners insurance will not pay for what is considered normal wear & tear or homeowner maintenance. Slab leaks are considered a little of both. Even if it is tree roots that bust a water line and cause the slab leak, the insurance company will see that as homeowner maintenance issues.  

However, if a peril that is beyond your control, causes a slab leak, you may get reimbursed for tearing out the slab, making the plumbing repair, and replacing the slab. A covered peril can be one of the following: 

  • Explosions
  • Falling objects
  • Fire
  • Wind

An example would be damaged to your home, including the slab, by a tornado. If you homeowner’s insurance policy states that wind damage is covered, then you slab leak repairs will be covered.  What if the tornado causes a slab leak in garage though? If your garage is detached, you’ll want to make sure your policy has “detached structures” or “other structures” coverage. An attached garage will typically be covered, but again, check your policy to be sure, before you need slab leak coverage!

What causes a slab leak?

Slab leak causes are typically from plumbing failures, like deteriorated and weak water lines or fault installation. How can plumbing pipe deteriorate? There are pipes made from materials that don’t fare well with the soil they’re buried under. Like Cast iron pipes.

Any home built before 1960s will likely have cast iron pipes. If the plumbing was connected above the ground, there probably won’t be any problem of deterioration. Cast iron pipe that was buried underground and unprotected though will become corroded by the minerals in the ground and the water flowing through them. Today, when cast iron pipes are used, they sheathed with a protective coating. 

Before the 1960s, galvanized steel pipes was the common plumbing pipe, but it is also susceptible to corrosion. In addition to that, galvanized water pipe clogs easier because the coating inside the piping wears off. This leaves them vulnerable to mineral and rust buildup, however, it can take up to fifty years before that becomes a problem. 

Today, rigid copper piping is used for underground plumbing lines and flexible copper piping is used for appliances that use water like the dishwasher and icemaker. Another type of plumbing pipe used today is plastic like PVC or flex plumbing. Both are corrosion resistant and easy to work with for installing and repairing, and very unlikely to cause a slab leak. 

In addition to the pipe materials used, another cause of slab leaks is the soil. Here in Texas, the ground contracts and expands all year long, and that can play havoc on slab plumbing, causing slab leaks. Studies by civil engineers tell us that one-fourth of all home in the country are on expansive soil and prone for slab leaks. 

Is a slab leak dangerous?

We are going to give you three reasons why a slab leak is more dangerous  and serious than a dripping faucet, although, the faucet should be fixed, you’re wasting a natural resource!  Remember, a slab leak you discover today has probably been happening for some time, they can go days, months, even years before they’re discovered. 

The three issues you need to be aware of that the slab leak you found today is causing you: 

  • Health: Your family’s health isn’t something to take lightly, but did you know that a slab leak is a potential health hazard? The water from a slab leak will become a breeding ground for bacteria, including mold. Breathing mold spores causes respiratory problems, which will worse over time because the moisture is still there, and the mold keeps growing and spreading. Once our respiratory system is attacked and breaks down, we become susceptible to other diseases and illnesses. 
  • Structural: A slab leak will weaken the integrity of the structure that you call home, even a home built with concrete and steel. Water pressure is mighty, and it will cause the ground under your foundation to shift, which will shift the foundation, causing it to crack. After enough time, the foundation is in danger of collapsing.
  • Financial: Because most, if not all slab leaks aren’t going to be covered by your homeowner’s insurance, the repairs of the foundation, the plumbing, and all other damages are going to come out of your pocket. That expenses could cost you up to $5,000 or more depending on where the slab leak is located and how bad the damage is to your home. 
leak through slab

What happens if you have a slab leak?

A slab leak will first saturate the ground under the foundation then the foundation. Because it has nowhere else to go, the water will begin to seep upward and under the carpeting and flooring of your home. It will work its way to the walls and upward, leaving mildew and mold behind with every drop and trickle of water. Some things you’ll start to notice are: 

  • You’ll notice doors and windows aren’t opening or closing easily, or maybe not at all. You may notice a rise in your water bill first, and then your home will always have a moist feel in the air.  
  • Family member may start experiencing respiratory issues, or if they have them already, they’ll worsen. That leads to more doctor appointments, missed days of school and work. 
  • A slab leak that goes unnoticed will cause the house to get lopsided, the broken slab could bust through the flooring, or cause the flooring to collapse where the foundation is sinking. 
  • The longer the slab leak goes, the walls become crooked, the roofing loses its stability because the frame of the house has lost its stability. Roof leaks and more begin happening and your homeowner’s insurance isn’t going to cover that because they will see it as homeowner neglect of foundation issues. 

Your first indication that you may have a slab leak, water bill increases, either drastically or gallon by gallon, a slow but steady climb. The minute you notice a water bill has increased, do the water meter check as discussed in this article. If that indicates you may have one, call a plumber immediately and have your home’s plumbing inspected. Don’t put of a slab leak repair, you’re only setting yourself up for more expenses. Call 817-281-5325 today for your slab leak repair in Fort Worth, TX.

How to protect your slab from the cold?

slab foundation

Slab leak foundation in the cold

The slab foundation of your home keeps it above the ground and so much more. It keeps your house warm, moisture out, and keeps your house from moving with the ground (well somewhat). 

A good foundation is made of steel-reinforced concrete that for most homes, is poured over the plumbing pipes. With slab foundation explained, this is where plumbing leak detection comes into our conversation today, along with winterizing your slab foundation or slab foundation with piers. 

If concrete is one of the strongest materials around, how does cold weather affect concrete? Yes, concrete is strong, but it can also be fooled with the temperature. Many contractors will tell you that you cannot pour concrete in cold weather, and that is at 40 degrees Fahrenheit or colder. Why? 

Concrete transmutes from a semiliquid to the solid material you’re familiar with due to hydration, a chemical reaction.  This means that when water and cement power are mixed together, a chemical reaction creates a process of  crystallization. Depending on the concrete’s temperature, it could process fast or slow, and the hotter the concrete thing it is, the faster it processes. 

A cold temperature slows the process down and the crystals continue to grow after the concrete is pour for months. This is called “curing” and the more it cures, the strong the concrete will be.  If the temperature gets colder than 14 degrees during the early stage of new concrete, those crystals quit growing, but they will start u again when the temperature warms. 

So, if your concrete foundation is poured when the temperature is cold, it won’t be able to withstand the pressure of a house. Furthermore, the plumbing that is laid before the found is poured is in jeopardy of leaking, and before you know it, your slab foundation is cracked and you’ve got a plumber with plumbing leak detection equipment in your yard. 

Will concrete crack in cold weather?

Yes it will and unfortunately, there isn’t much you can do about it. Concrete is porous and when there an abundance of ice, rain, or snow, is on the surface, the water from those leaks into the concrete. Then, in the winter especially, the temperatures drops and that moisture inside the concrete freezes, expands the concrete. As the temperature warms up, the ground warms and thaws, and the concrete contracts and that is what causes it to crack. 

How do you fix water seeping under foundation?

Groundwater that is seeping under your foundation is happening because of excessive water in the ground near or next to the foundation wall or the basement. As groundwater pressure builds, that is when it begins to seep through cracks in the foundation. Fortunately, there are some things you can do that can thwart that seepage:

  • Build the yard up near the foundation so that it slopes consistently away.
  • Make Certain that all downspouts and the sump pump flows away from your home toward the yard. 
  • Make sure the basement drains consistently toward the floor drain.
  • Have the foundation wall waterproofed. 

Can you pour concrete footings in cold weather?

Yes, but there are several precautions recommended that you’ll need to coordinate with the contractor pouring the concrete footings: 

  • Do not have the concrete poured when the ground is frozen or covered in ice or snow. 
  • Place insulated blankets over any freshly dug earth to preserve the subsoil with its natural warmth. The blankets can be removed just before the pour starts. 
  • Request the builder use an air-entrained concrete. This is the addition of chemicals to the freshly mixed concrete that will create millions of microscopic air bubbles which will help the concrete dry faster and cure as they act as shock absorbers if the water mixed with the concrete freezes. Instead of the water freezing in the concrete, it will freeze in the air bubbles created. 
  • Request the contractor use a heated mix or have  100 extra pounds of concrete for every cubic yard. Either of these will help the concrete to develop strength earlier in the process. 
  • Confirm the contractor is using a dry mix or a low slump of four inches to minimize bleed water. Because water is the lightest ingredient of this process, as the slab is poured, you’ll see a formation of water beads on the surface. Any trowel usage too soon will weaken the concrete. A low-slump type of concrete will finish quicker and can be covered with insulated blankets sooner. 
home with a slab foundation

Will concrete cure in the cold?

Yes, but there are some special factors that should be followed for a solid cure when the temperatures are at or below freezing. Remember when the air is below or will fall below 40°F, then use cold weather techniques.

  • Pouring concrete in cold weather must be cured. The surface will dry out faster if the concrete is warmer than the surrounding air.
  • Finishing concrete in cold weather still requires waiting for evaporation of the bleed water, allowing the concrete particles to settle and squeeze any extra water. If water is finished into the surface, there is an increase chance of having a weak concrete surface. 
  • Use less water for the concrete to cure in cold weather. More water keeps concrete soaked, making it susceptible to freezing and causing damage. 
  • Using a concrete additive can eliminate or reduce any need to use protection in cold weather. 

Call 817-281-5325 today for your slab foundation repair in Fort Worth, TX!

What Does a Plumbing Inspection Involve?

Plumber with Plumbing tools on the kitchen. Renovation.

Learn More About Plumbing Inspections

Your plumbing system is complex and will require proper care and maintenance routinely. A plumbing inspection is a great way to analyze the condition of various parts of your system and determine if any plumbing services are needed for improvement of performance. Get in touch with an established plumbing company in order to get professional services. A plumbing inspection will involve checking many areas of a plumbing system and in order to get the most out of it, a trained professional that’s knowledgeable of the job is essential. Before you reach out to a plumber, here is a little background information regarding plumbing inspections that may prove useful to you.

When is a plumbing inspection required?

A plumbing inspection will be required in the process of home buying in order for issues to be identified and fixed before purchase. In general, for homeowners, a plumbing inspection is recommended yearly at a minimum in order to make sure that any minor damages that may have accumulated over the seasons can be fixed before more severe damages come about. You may also need an inspection after harsh weather conditions such as frozen pipes, which can run the risk of pipe bursts, or if you’re noticing odd behaviors with your plumbing system. With a plumbing inspection, you’ll be able to improve the efficiency and performance of water, locate clogs and leaks more easily and save pipes before they fail in certain cases.

How long does a plumbing inspection take?

The amount of time a plumbing inspection will take will depend on the size of the house, the number of problems found, and other specifications that come with the property. Expect a plumbing inspection to take around two hours on average. 

How do I pass a plumbing inspection?

In order to pass a plumbing inspection, there will be several things that will need to be in proper conditions such as proper water pressure, secure pipe connections, and more. Since there are several areas of the home that will need to be checked it may be best to have a professional gauge what is in proper condition for your home.

What does a plumbing inspection consist of?

A plumbing inspection will have all areas where water or wastewater is running checked through the property. This will include toilets, sinks, pipes, tubs, showers, laundry rooms, garbage disposals, waste lines, and more. Supply lines and shut off valves will also be checked.

What do home inspectors look for in plumbing?

A home inspector will differ with plumbing inspections as they check various other systems of the home as well. Yet as far as the plumbing aspect of the inspection they will examine supply lines, fixtures, drains as well as water filtration systems. There will be an in-depth inspection of all above-ground exposed plumbing such as with traps under sinks, the bathroom, laundry room, shut off valves, sinks, showers/bath, and toilets.

What is a top out plumbing inspection?

A top-out plumbing inspection otherwise known as a 2nd rough-in includes all supply and DWV lines that will be covered up. Water lines are pressurized and stub out checked to see if ok for fixture valved on the trim out.

A pipe leaking with freeze damage

How do I know if my plumbing is bad?

  • Water Stains
  • Bad Smells
  • Low Water Pressure
  • Slow Moving Drains
  • Running Toilet
  • Dripping Faucet
  • Clogs
  • Leaks

What is considered a plumbing emergency?

A plumbing emergency can come about from slab movement causing pipe leaks, frozen pipes bursting, weather conditions halting the movement of water, gas leaks, blocked drains, tree roots infiltrating the plumbing lines, sewer problems, septic tank issues, and more. Essentially a plumbing emergency will halt the use of water or cause damages to the plumbing line that can alter the progress of regular use. Ignoring the issue for certain cases may cause further issues which is why an emergency plumber is typically called for a plumbing inspection and repairs. Keep in mind that an emergency plumber will typically have an extra cost as they are being called out immediately or within 24 hours.

Can bad plumbing make you sick?

Bad plumbing can be hazardous to health with poor water quality being absorbed in your skin or in certain cases it can expose you to Salmonella, E. Coli, or even Hepatitis. With sewer leaks, you may be exposed to toxic conditions and other risks.

How do you know if your sewer line is leaking?

You may be able to notice several signs that your sewer line is leaking. There will be unpleasant odors as expected, sometimes there can be uncommon sounds coming from pipes like the sound of running water, floors can be moist or spongy with underground pipes, cracks can form on walls, the foundation, or other areas of the home, there will be higher water bills, landscape growth, and in certain cases problems with rats. Sewer line leaks can be hazardous to the health of occupants so make sure to have a professional plumber conduct a plumbing inspection to gauge where the leak is located so that repairs can be made as soon as possible. 

Contact a Qualified Plumber For a Plumbing Inspection Today

If you’re in need of a plumbing inspection reach out to your local plumbing company for assistance. Only a trained and certified plumber will be able to safely follow protocol and handle your plumbing connections in the right way in order to avoid causing further problems. They will be able to work in accordance with your property specifications and have the knowledge and experience of knowing what to look for no matter the type of plumbing system that you have. Find out the conditions of your plumbing system today and get a plumbing inspection soon.

To get assistance with a plumbing inspection in Fort Worth, TX call 817-281-5325 with Slab Leak Solutions! 

When Is It Time to Repipe a House?

planning a repipe project

Whole house repiping

If you’ve heard about or your plumber has recommended it, your first thought is probably What is home repiping, and that is what we will discuss here by answering the common questions. In addition to discussing when is the right time for home repiping, we’re going to talk about Why is home repiping a good idea too.

First, what are the benefits of home repiping? Home repiping is what it says, repiping a hoe with new pipes. Sometimes, the plumbing in a home is in serious condition that the only way to fix it is to rip it all out and start over. In basketball 3-on-3 they call it “do over”, but what good does total home repiping do? 

  • Improves water pressure: Low water pressure is aggravating and often is caused by pipes that are old and corroded. With total home repiping using copper or PEX, the water pressure is improved immediately. 
  • Improved home value: Whole home repiping will improve your home’s values and make it more appealing to possible buyers should you decide to sell later because it gives them a sense of security and you get peace of mind while living here.  in the process.
  • Plumbing leaks prevented: Once you have a whole home repiping done, your worries of water pipe leaking are over, and with that, concerns of mild and mold growth from water damage, is gone. Home repiping with PEX piping will make your plumbing resilient to freezing in the winter too. 
  • Safe plumbing: with whole home repiping option of PEX, the pipes are corrosion and rust-resistant, making your water safer with less chance of bacterial growth.
  • Rust-free water: Whole home repiping will get rid of the old plumbing that has rusted inside. 

What is involved in a whole house repiping project?

Typically, a total home repiping involves removing the old plumbing pipes, often galvanized steel, and replacing it with newer materials, either PEX or PVC. These newer materials offer durability, freeze resistance, and longevity. The steps involved are: 

  • Cover areas with plastic sheets
  • Cut ceiling and drywall with surgical style cuts 
  • Remove the old piping
  • Install new piping
  • Patch the ceiling and drywall

How long does it take to repipe a whole house?

There are two main factors that will determine how long a whole home repiping will take. One is the size of the home. The more piping involved, the longer it takes. A one story home with two bathrooms can be completed faster than a two or three story home with three or more bathrooms. The other factor will depend on the existing plumbing type. The average one story, two bath home with laundry room can take up to two days.

When should I repipe my house?

Unlike the filter on your HVAC system that should be changed monthly (you’re welcome for that reminder), there isn’t an exact scheduled timetable for total home repiping. So, should you repipe your house? A home that is fifty years or older is likely in need and an experienced plumber could inspect your plumbing and advise you accordingly. 

What if your home is less than 50 years old, but has lead pipes?  Then you should definitely have total home repiping done. Why? Lead pipes for plumbing have been outlawed in most of the country, if not all of the country due to the health concerns and issues they cause. Even the best water filters can not assure clean, safe water coming from lead pipes.

Should I repipe my house with PEX?

Yes and no. PEX is susceptible to damage by UV rays, so if you choose to go with PEX for your home repiping, you want it protected from the sun, which usually isn’t an issue since most plumbing is under the house or inside cabinets and walls. You should also know that PEX is not rodent resistant, so if you have issue with rodents in your home, that needs to be addressed before installing, or when you install PEX plumbing. 

Because PEX is a flexible material, if your plumbing begins having issues after your home repiping, and the piping is rubbing from vibrations, typically air in the lines, that should be remedied quickly to avoid rubbing a hole in the PEX and a leak starting. 

pex piping and joints for whole home repiping

Does insurance cover repiping?

Yes, home repiping is expensive, so most homeowners would love to file this on their homeowner’s insurance.  Most likely, your homeowner’s will not cover total home repiping simply because you want better water pressure. 

However, if your home has been damaged by corroded and failing water pipes, it will cover the repairs of damage caused by the old piping, and possibly it will cover the cost of the pipes used to replace the damaged, old pipes. Review your policy with your agent and see if a total home repiping could be covered even partially. Call 817-281-5325 today for whole house repiping in Fort Worth, TX.

Can a Thermal Imaging Camera Detect Water Leaks?

Thermal camera leak detection

Can a Thermal Imaging Camera Detect Water Leaks?

Thermal camera water leak detection is very important when you surmise that you may have a leak in your home or property. It is important to stipulate that a thermal imaging camera does not have the power to glimpse moisture in walls. However, these cameras are capable of detecting subtle temperature differences and patterns that can reveal the existence of water. As any technician who specializes in the industry can attest, moisture is one of the most difficult things to detect in a building. After all, the symptoms for moisture are subtle and very easy to miss until water starts falling from the ceiling.

Can FLIR Detect Water Leaks?

If you are wondering whether or not FLIR can detect water leaks, it is important for you to review what great thermal cameras can do. The FLIR E6 is used for basic uses, and the E8 and E95 are great for higher resolution options. It is true that thermal cameras can help locate water and approximate the moisture extent, but when it comes to identifying a pattern that looks like moisture, it’s important to understand that it does not guarantee the presence of water. That is why it is important to understand the strengths and limitations of current technology.

How Does a Thermal Leak Detector Work?

Are you wondering how a thermal leak detector works? If so, please review the following list to discover more.

  • Each object gives off infrared light. Even cold objects emit some kind of infrared light.
  • A thermal leak detector measures the amount of infrared light that it emitted off of a surface.
  • The measurement of infrared light is then calculated to determine the temperature.

Can a Thermal Camera Detect Moisture?

While it must be continually noted that a thermal camera cannot actually observe the moisture that may be latent within walls, it can detect subtle temperature differences. These subtle temperatures differences can reveal the existence of water inside the walls. As previously mentioned, water is one of the most difficult and important elements to detect. That is because water damage can be particularly dangerous for the structure of the building. If you suspect that you have water in your walls, it will be important to contact a professional technician as soon as possible.

Can You Tell Where Cold Air Is Coming From?

One of the important things for homeowners to understand is that there are troubleshooting options available when cold air is coming into your home. When you don’t know where the cold air is coming from, you can start by checking your attic, basement, and crawl spaces. In these areas, you should review any cracks, gaps, and openings where cold air can be coming through. Alternatively, you can try a smoke test. You can do this by waiting for a windy day and then shut all windows and doors. You will also need to turn off all appliances. Next, you will hold a lit incense stick next to any potential air leakage spots.

Thermal Camera Leak Detection

Are you wondering whether or not thermal camera leak detection is a new technology? Believe it or not, using infrared cameras, also known as thermal imagers, to detect moisture and building failures is a new but rapidly growing practice. The industries that rely on this technology most are in the insurance and inspection arenas. In the roofing industry, infrared technology has also been put to great use in detecting roof failures. The fire and water restoration industry has also been able to make infrared cameras a vital part of operations.

Thermal Imaging Camera for Water Leak Detection

One of the most intriguing questions that can be posed to an infrared camera specialist is whether or not fish can be detected with infrared technology. As a matter of fact, as long as the water temperature changes rapidly within a few meters, the camera can tell the difference. Thermal cameras can also “see” fish at night.

Best Thermal Camera for Leak Detection

There are a number of different excellent thermal cameras available on the market. Ultimately the choice will be up to the consumer. However, the Black and Decker TLD100 is very highly rated, as is the Seek Thermal Compact Imager for iOS-Apple.

Thermal camera leak detection

Thermal Camera for Leak Detection

Thermal cameras have a great variety of uses in many different industries. If you believe that you have a water leak in your home, it will be important for you to move forward with a proper inspection. A respected and reputable company in your area will be able to help you navigate a positive pathway forward.

If you need thermal camera leak detection in Fort Worth, TX, please reach out to us at 817-281-5325 today. Our friendly staff would be happy to provide the best assistance.

What does Repiping mean?

measuring piping

Updating Your Home From the Inside Out

If you’ve heard somebody talk about getting repiping done, you’re probably wondering what is repiping? The pipe in a home is susceptible to being damaged through a natural progression over time, i.e., they’re aging. Or root infiltration can disrupt piping. Fortunately, with whole house repiping, we have a solution to fix those disruptions and more.

What does repiping mean?

Whole house repiping is the process of removing damaged, detached, or older piping and replacing it with new pipe materials. With pipes that are damaged, detached, or worn, it becomes essential to get a whole house repiping service done to prevent water penetration in the soil that can cause slab movement. Additional slab movement puts the foundation’s integrity in jeopardy and causes more problems. 

plans for a repiping project

What does a repipe include?

A whole house repiping job involves cutting small holes inside your home at the walls, digging trenches around your property and under your house, and accessing an area for the repiping machine can be placed to do the repiping without extensive damage and to dig up the landscape. 

There are different techniques for a whole house repiping that technique that pushes the older pipes out as the new pipes take over the existing connections and space. Whole house repiping allows you and your plumber to choose from several options that are corrosion-resistant, rust-resistant, and flexible. 

So, we discussed what a repipe includes. So, if you had a plumber inspect your plumbing and they found a pressurized leak, the most common reason for a whole house repiping. What should you expect with a whole house repiping? 

Included in Whole house repiping

Included in Whole house repiping

  • Replacing all water lines running to each plumbing fixture.
  • New connections.
  • New sink and toilet valves.
  • Replaced water supply lines.
  • Replaced main shut off to the house and the water heater.
  • Replaced laundry box, including valves 
  • I replaced the ice maker box.

Not Included in Whole house repiping

  • Water Main between city meter and house. 
  • Drain lines, including pipes underground, inside walls, and vents. 
  • Leaking in shower, sinks, or tub.
  • Toilet leaks.
  • The main sewer line between house and street.
  • Water heater replacement.

Is repiping necessary?

Looking at a house, it may appear to be completely fine, but then you get a look at the pipes. Yes, the plumbing pipes tell a story that you may not know otherwise. 

There could be pipes that are cracked, rusted, or is beyond repair. These are the kind of houses that are good candidates for whole house repiping. If the pipes in your home look like this, or there seems to be missing pipe, call a professional plumber to inspect your home’s plumbing and give you an estimate. 

When should I repipe my house? 

The easiest way to determine when Whole house repiping time is needed is to call a professional plumber. However, it would be best if you did some assessment yourself before making that call. Here are seven signs that are giving you subtle hints; it is time to schedule a whole house repiping. 

  • Pipes Are Aging or Unsafe
  • Pipes Are Constantly Leaking. 
  • Corrosion on Pipes.
  • Bad Water Pressure. 
  • Discolored Water.
  • Funny Taste or Bad Odor From Water.
  • Temperature Fluctuates

Is Repiping covered by insurance?

No, whole house repiping is considered a preventive measure, not an insurance covered need. However, check your policy about coverage for damage caused by pipes corroding or failing. 

prepping for whole house repiping

Closing Words

Most of the plumbing in a house is out of sight, so it is out of mind until the faucet or drain that is insight has problems. Whole house repiping can fix many of those small annoying things that are happening. You maybe wonder what about the whole house repiping disadvantages? It sounds great, but there has to be a catch, right? The disadvantage is not doing it, and the expense of doing it, and both of these can be outweighed by Whole house repiping time benefits you get by having a whole house repiping job done.  

The benefits to be gained are: 

  • Upgraded Pipes: Piping won’t last forever, a surprise for most of us to hear. Copper piping lasted as long as 80 years, and galvanized steel pipes last around one hundred years. 
  • Replacing Outdated Materials: if you have a home built before the 1990s, you need updated piping. 
  • Fix Water Pressure: Whole house repiping will change your home’s water pressure. 
  • Fix Water Color: Whole house repiping gets rid of the dark, rusty color in your water. 
  • Leak Protection and Water Damage Protection: Why wait until something breaks and leaks? A whole house repiping will fix the problem before it becomes a problem. 

Whole house repiping doesn’t have to be overwhelming, so no matter why you’re having your home repiped, with the right plumbing contractor, it should go smoothly. They should take the time to explain the job to you and answer any questions. It is the unknown that causes us anxiety and worry, especially when it involves our family or our homes. Connect with our team now by dialing 817-281-5325 for information about whole house repiping in Fort Worth, TX.

Should I Do a Sewer Inspection?

A Technician Hooks Up a Plumbing Video Inspection Camera.

Should I do a sewer inspection?

There are many reasons you’d want to have your sewer lines inspected. Obviously, if you suspect your sewer line is clogged or backed-up or otherwise damaged, you’ll want to have your sewer lines inspected. You especially want to have the sewer line inspected if you are buying a house. A plumbing video inspection of the sewer lines isn’t always part of a standard home inspection, but should be performed. This is one of the best ways to catch potential problems like a potential back-up or find tree roots invading the line. These are problems you don’t want to encounter a few weeks after moving into your new home. You don’t want to have to pay for repairs after you move in, especially if you’re going to end up having your yard torn up and spend thousands of dollars repairing damaged pipes.

Many plumbing professionals also recommend getting your sewer lines inspected as part of regular plumbing maintenance to catch, avoid, or prevent problems like back-ups. Whether it’s part of a new home inspection or regular maintenance, when you need a sewer drain camera inspection or plumbing inspection in Fort Worth, TX, look to the professionals at Slab Leak Solutions. You can set up an inspection by calling 817-281-5325.

How long does a sewer line inspection take?

Typically, a plumbing video inspection of the sewer lines takes about an hour. Sometimes an inspection will take longer. The time it takes to perform the inspection will depend on how easy it is to access the sewer lines, how long the lines are, how many turns you have to navigate, and what problems are encountered. 

Can you rent a drain camera?

Yes, sewer drain cameras can be rented. You may be able to rent them from big box home improvement and hardware retailers or equipment supply companies. Check with retailers or supply companies to see what is available in your area. If you are planning to do a plumbing video inspection you’ll be wondering “How do you use a pipe inspection camera?”

Actually, using the camera is a fairly simple process.

  • Insert the camera into the main sewer line cleanout or vent stack.
  • Snake the camera through the sewer line.
  • Follow the camera’s progress on the camera’s video monitor.
  • Look for blockages such as mud or tree roots.
  • Use the location device on the camera to determine where the camera is when a blockage is found.

If you are trying to find a leak with a sewer camera, it will be very difficult to tell if you have a leak with just the camera alone. You’ll need a plumbing inspection camera with locator to find leaks. Even with this equipment, leak detection using a camera can be difficult, especially if you are unsure about what you’re looking for, especially because you are looking inside the pipe and leaks are going to be outside the pipe. Sewer lines are especially difficult because waste material builds up on the inside of the pipe over time. If you get help from a leak detection specialist like Slab Leak Solutions, we have other equipment like sound devices that make it easier to detect and locate leaks.

Commercial plumbing video inspection

A plumbing video inspection for a commercial building can be complicated, especially given the size of most commercial buildings, and the amount of piping in them. Still, you do not want to neglect any repairs you may need, and video inspection is very useful when it comes to finding problems like blockages. Neglecting repairs could lead to problems with the health department or with insurers.

How do you replace a sewer line under a slab?

Most of your sewer lines run underneath your home’s foundation, or slab. If there is a leak or the line is otherwise damaged the line will have to be repaired or replaced. There are a few options that can be taken for repairs. In some cases, the leak will have to be located and it may require plumbers or leak repair specialists to dig through the foundation to get to the damaged pipe. A more recent innovation in repairs is tunneling, in which professionals locate the leak and then dig under the foundation to get to the damaged pipe and make the repair while underground. 

Other options include pipe relining and pipe bursting. With relining, an epoxy-coated tube is sent through the damaged pipe to reline it. This fix narrows the pipe slightly but is very effective. With pipe bursting, a whole new pipe is dragged through the old pipe, bursting it, so the new pipe takes its place. In extreme cases, if there are problems like multiple leaks or all the piping is old and corroded, the home may need to be repiped. Before repairs are made, a plumbing video inspection is required in which a camera is sent through the lines to find problems like blockages and sometimes leaks. 

Sewer Line Under a Foundation.

Video plumbing inspection near me

If you think you might have an issue in your sewer line or main water line and need a reliable plumbing video inspection in Fort Worth, TX, look to the experts at Slab Leak Solutions. We have the right tools like cameras and sound equipment to detect leaks and blockages in all your lines and drains. Find out more or schedule a service by calling 817-281-5325.